Dana Motion Systems is the hydraulic division of Dana Off-Highway Motion and Drive Technologies and is the result of the acquisition by Dana of the Brevini Fluid Power business. Brevini Fluid Power was established in 2003 through the merger of several companies active in the hydraulic sector for over forty years.
KRA Cartridge valves with electrical position control This valve serie is used in those applications where monitoring of the actual valve position is required for managing machine safety cycles as required…
Screw and studs for CETOP 5/NG10 valves
Gear Pumps OT2HR: Hercules SeriesThe gear pumps construction include a gear housing, mounting flanges and covers in cast iron material.Thanks to this construction the Hercules gear pumps can be used in…
Gear Motors OT2HR: Hercules SeriesThe gear motors construction include a gear housing, mounting flanges and covers in cast iron material.Thanks to this construction the Hercules gear motors can be used…
Gear Motors OT2HR: Hercules SeriesThe gear motors construction include a gear housing, mounting flanges and covers in cast iron material.Thanks to this construction the Hercules gear motors can be used…
Gear Pumps OT2HR: Hercules SeriesThe gear pumps construction include a gear housing, mounting flanges and covers in cast iron material.Thanks to this construction the Hercules gear pumps can be used in…
The gear pumps construction include a gear housing, mounting flanges and covers in aluminium material. They offer very good mechanical and volumetric efficiencies: the right gear pumps for power packs.Displacements…
The gear pumps construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear pumps can be used…
The gear pumps construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear pumps can be used…
The gear pumps construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear pumps can be used…
The gear pumps construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear pumps can be used…
The gear pumps construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear pumps can be used…
The gear pumps construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear pumps can be used…
The gear pumps construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear pumps can be used…
Silent Plus Series: Group 2 European Standard PumpsThe Silent Plus gear pumps represent a very good solution to reducing noise level. The project includes the use of helical gears that reduce down the…
The gear pumps construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear pumps can be used…
The gear motors construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear motors can be used…
The gear motors construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear motors can be used…
The gear motors construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear motors can be used…
The gear motors construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear motors can be used…
The gear motors construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear motors can be used…
The gear motors construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear motors can be used…
The gear motors construction include a gear housing from extruded in aluminium alloy and mounting flanges and covers made in cast iron material.Thanks to this construction the OT gear motors can be used…
The gear pumps construction include a gear housing, mounting flanges and covers in aluminium material. They offer very good mechanical and volumetric efficiencies: the right gear pumps for power packs.…
OT OilTechnology offers a valid and complete range of flow dividers group 1. The OT100 flow dividers can be used as flow equilizators (with same displacement on each section) or as flow dividers (with…
OT OilTechnology offers a valid and complete range of flow dividers group 2. The OT200 flow dividers can be used as flow equilizators (with same displacement on each section) or as flow dividers (with…
Silent Plus Series: Group 2 European Standard PumpsThe Silent Plus gear pumps represent a very good solution to reducing noise level. The project includes the use of helical gears that reduce down the…
Directional control bankable valve
Module units no pressure relief valve
Module units FE305 with adjustable pressure relief valve (up to 80l/min)
Outlet module
Intermediate element with pilot operated check stackable valves
The H1V PV pumps have been specially designed for pumping and metering polyurethane components with viscosity in the 1-2000 cSt range (polyoils and isocyanates). The high repeatability of the delivery…
The HD1 series variable piston pumps for closed loop circuits are axial pistons pumps with swash plate design and through drive shaft on option. These pumps have been specifically designed for use in closed…
The sequence valve are used to assure that a secondary circuit is pressurized when the setting pressure is reached. These valves grant a minimum variation of the setting pressure with a changing flow up…
With proximity sensor LVDT
Lever operated valves
Actuator load pressure selecting units, as they are fitted with an integral shuttle valve cartridge which allows taking of the highest pressure signal to the external port via displacement of a ball. They…
One way non-compensated throttle valve are fitted with an O-Ring mounting plate which allows its assembly for either input or output regulation. Adjustment is obtained by means of a grub screw or a plastic…
H2V series are variable displacement bent axis, axial piston motors for operation both in open and closed circuit. The bearing of main shaft allows operation with both high radial and axial loads. Several…
AD3P Pneumatic AD3O Oleodynamic AD3M Mechanically AD3D Direct Mech.
Closed center inlet module for variable displacement load sensing pumps
Pressure reducing and sequencing valves CETOP 3/NG6. These subplate mounting piloted type pressure reducing and sequencing valves ensure a minimum variation in their calibrated pressure value with changing…
This is an intermediate block for modular mounting of one or two flow rate regulators type QC3 The flow regulator type QC32 must be ordered separately.
Pressure reducing and sequencing valves CETOP 5/NG10. These subplate mounting piloted type pressure reducing and sequencing valves ensure a minimum variation in their calibrated pressure value with changing…
SH7V series are a family of variable displacement motors, bent axis piston design for operation in both open and closed circuit. The proven design incorporating the lens shape valve plate, the high quality…
BS5RIA Special subplate mounting with automatic exclusion regenerating circuit.BS5RGA Special subplate mounting with automatic exclusion regenerating circuit.
These pressure control valves are available in the basic VMP* maximum pressure, VSP* sequence and VUP* exclusion versions, with a single pressure value and three calibration ranges that cover the band…
A09 DC coils 20W DC Coils for off-highway machinery D15 DC coils for Cetop 3 Hirschmann eCoat Coils (D15 RS R6 variant) 40W DC coil (for CDL06) B14 AC Solenoids for Cetop 3 A16 DC coils for Cetop 5 D19…
This is modular assembly ON/OFF solenoid valve which, by fitting suitable 2 way regulator, allows two speed operation in the same system via an electrical changeover command.
Stackable proportional directional valves with LS signal locally compensated. Used for controlling fl uid direction and flow rate as a function of the supply current to the proportional control solenoid.
2 Way compensated flow rate regulators with adjustable P. Compensated flow regulators with antijump system and adjustable differential pressure can be defined as hydraulic power control units. Their design…
22W DC coils 27W DC coils
SH7VR series are a family of variable displacement motors, bent axis piston design, for operation in open and closed circuit. SH7VR series motors are plug-in motors for gear boxes, for combinations such…
ON/OFF Compensated Valves with single or double solenoid, LS signal locally compensated. Used for controlling fluid direction and flow rate. Flow rate controlled by the valve predefined by a holed calibrated…
This modular valve produces a regenerative system to increase the actuator (differential cylinder) exit speed as shown in the diagram. In particular, if a cylinder is used with a 2:1 ratio for the operating…
Outlet module unit
Electronic regulators for double solenoids proportional control valves. The electronic control card type REM.D.RA has been designed to drive the double solenoid proportional valves series “XD.*.Cand XDP.3.C”…
XD.3.A.. / XD.3.C.. series valves are used for controlling fluid direction and flow rate as a function of the supply current to the proportional control solenoid. Any valve p variation causes a change…
Inlet module units with LS line, compensator and pressure relief valve
3 way compensated flow rate regulators. This regulator type can be used whenever it is necessary to obtain a constant fluid flow irrespective of the pressure variations present upstream or downstream.…
Screw and studs for CETOP 2/NG04 valves
Inlet module units with side ports and pressure relief valve
Screw and studs for CETOP 3/NG06 valves
XDP3 Proportional directional valves open loop. The open loop valves of series XDP control the direction and the volume of the flow according to the feeding current to the proportional solenoid. By using…
MD11V series are a family of variable displacement motors, swash plate design for operation in both open and closed circuit. The high quality components and manufacturing techniques make able the MD11V…
Units of SH11C series are a family of motors and pumps with fixed displacement thant can be used both in open and closed circuit. The SH11C fixed series motors features 40° bent axis angle and offer machine…
Compensated flow regulators with antijump system and adjustable differential pressure can be defined as hydraulic power control units. Their design is suitable to circuits in which the flow rate has to…
Inlet module units with pressure relief valve for proportional pressure compensated flow regulator XQP3 17
XDC3 Proportional directional valves closed loop position control. The valves XDC serie 2 control the direction and the volume of the flow according to the feeding current to the proportional solenoid.…
Inlet module units with pressure relief valve and electrical venting valve
SH11CR series are a family of fixed displacement motors, bent axis piston designed for operation in open and closed circuit. SH11CR series motors have a plug-in flange to be mounted on gear boxes, to fit…
Modular check valves allow free flow in one direction, while a conical seated poppet prevents flow in the opposite direction. They are available on single A, B, P and T lines, and on double A and B, P…
XQP3 Open loop 2/3 way proportional pressure compensated flow regulators. The open loop proportional flow regulator is 2 and 3 way compensated with priority function. It is designed to regulate flow in…
XQ3 Proportional flow control valves pressure compensated. This is a proportional valve where both the flow rate and pressure control flow functions have been integrated according to the 3 way regulation…
Intermediate element
AM5UP type modular check valves allow free flow in one direction by lifting a conical steel seated poppet, while in the opposite direction the fluid can return by means of a small piston piloted by the…
Intermediate element with LS line
Pressure relief valves are available within operating range 7 350 bar. Adjustment is by means of a grub screw or a plastic knob. They are three basic versions: AM.5.VM, on single A or B lines, and on…
Intermediate element with pressure reducing valve
XP3 Proportional pressure control valves. Proportional maximum pressure valves type XP.3.*.. are used to regulate a hydraulic circuit pressure by means of a variable electric signal. Their precise implementation…
Directional control valve connection B-P for Intermediate element FI3BP
AM3XMP Amplifier valves for proportional control valves. Modular valve type AM.3.XMP used together with the pressure proportional pilot type XP.3.. becomes a pressure control valve piloted by proportional…
These pressure reducing valves ensure a minimum pressure variation on the P or A port with changing flow rate up 90 l/min. Three spring types allow adjustment with the range 7 250 bar. Manual adjustment…
Back pressure valves are direct acting damped maximum pressure in-line valves fitted with bypass non-return valves. They are obtainable within the adjustable range 2 250 bar. Adjustment is by means of…
XDP5 Proportional directional valves open loop. The open loop valves of series XDP control the direction and the volume of the flow according to the feeding current to the proportional solenoid. Each p…
Intermediate element for valve CDC3R
Outlet module units with side ports
The sequence valve are used to assure that a secondary circuit is pressurized when the setting pressure with a changing flow to up 90 l/min. Three spring types allow adjustment within the range 7 250…
XQP5 Open loop 2/3 way proportional pressure compensated flow regulators. The open loop proportional flow regulator is 2 and 3 way compensated with priority function. It is designed to regulate flow in…
Modular valves are actuator load pressure selecting units, as they are fitted with an integral shuttle valve cartridge which allows taking of the highest pressure signal to the external port via displacement…
BG series motors feature spool valve design and gerotor gear set. They are economical motors able to accomplish light to medium duty applications.
Outlet module units with overcenter and top port
OPEN CENTER inlet module with compensator for fixed displacement pumps
One way non-compensated throttle valve are fitted with an O-Ring mounting plate which allows its assembly for either input or output regulation. Adjustment is obtained by means of a grub screw or a plastic…
Spool valve design and gerotor gear set hydraulic motor with compact design and small displacement. Suitables for application where high speed and small dimensions are required.
The Self leveling Device LAB3 meets the safety requirements: Category 3 (EN954-1) PL d (EN13849-1) The card has two outputs PWM current feedback to control a proportional valve, a safety relay output to…
This is an intermediate block for modular mounting of one or two compensated flow rate regulators QC3. The flow regulator type QC32 must be ordered separately.
Hand pumps are generally employed for intermittent or emergency applications. The wide range for integrated applications with auxiliary valves allow the solution of any requirement.
Post compensated FLOW SHARING valve High efficiency energy saving
For the control of variable displacement pumps and motors.BPE terminal : Software di interfaccia utente per parametrizzazione e messa in servizio prodotti elettronici:BPE TerminalDriver USB per convertitori…
This modular system produces a regenerative circuit to increasing the actuator (differential cylinder) exit speed as shown in the diagram. In particular, if a cylinder is used with a 2:1 ratio for operating…
This is a modular assembly ON/OFF solenoid valve which, by fitting a suitable 2 way regulator, allows two speed operation in the same system via an electrical changeover command.
The MAV1152HY controller unit is used for the control of one proportional solenoids and additional switching valves. The proportional solenoid output is pulse-width-modulated (PWM) and optimally adapted…
The EP and MP series of electric pumps are simple power unit composed by DC motor and gear pump, usefull where the filled circuit is far from the the power unit.
CTM are part of the Spicer product offer. Please click here for more information.
The low/high pressure groups are usually employed in hydraulic systems fed by dual pumps that form a single pressure circuit. The main feature of this system consists in being able to set a pressure value…
MAV4211: Electronic module for integrated control of proportional valves, bankable valves and proportional directional valves HPV Brevini Fluid Power. The MAV4211 controller unit is used for the control…
Modular check valves allow free flow in one direction by lifting a seated poppet, while in the opposite direction the fluid can return by means of a small piston piloted by the other line pressure (piloted…
One way non-compensated throttle valve. Adjustment is obtained by means of a grub screw. They are available in the three regulating configurations shown in the hydraulic diagrams. All configurations have…
The BR series motors feature spool valve and roller gear set design. They offer compact, design, high efficiency, good smooth rotational speed and good starting torque.
Modular pilot operated check bankable valves
Orbital motor with roller design and spool valve distributor. Motion control valve and disengagment brake port as optional. Available with displacement from 50 up to 400 cm3/ giro [from 3.05 up to 24.4…
Coils for valves
The low/high pressure groups are usually employed in hydraulic systems fed by dual pumps that form a single pressure circuit. The main feature of this system consists in being able to set a pressure value…
The 6 way fl ow diversion valves, are special solenoid valves which allow the simultaneous connection of two systems. With all user ports on the same side, these valves allow to simplify the layout of…
Sandwich design for easy configuration, servicing and interchangeability. Closed center for variable displacement pumps with Load Sensing and Constant Pressure control. Open center for fixed displacement…
Modular max. pressure bankable valves
High performances solenoid operated valves
Interface with HPV41 module
The stackable circuit selector valves, allows one single drive of 6 users with 5 elements connected in series. As they are moved from high performances solenoids they dont need the external drainage. This…
With proximity sensor LVDT
The gearboxes of the ML and B series are used mainly for connecting hydraulic pumps to the power take-offs of agricultural tractors. PTO output, standardised at either 540 or 1,000 rpm, is, in this way,…
Automatic reciprocating valves CETOP 3/NG06
The bell housings of the HL series and the couplings of the HE HF and GB series are utilised in the construction of hydraulic power packs and serve for coupling hydraulic pumps to UNEL-IEC standardised…
XD2A../XD2C.. series valves are used for controlling fluid direction and flow rate as a function of the supply current to the proportional control solenoid. Any valve p variation causes a change in the…
The supports of the SU series are used to drive hydraulic pumps and transmit the motion of hydraulic motors where there are strong radial and axial loads. The mechanical clutches of the IM series and the…
SH9V series are a family of variable displacement motors, bent axis piston design for operation in both open and closed circuit. The proven design incorporating the lens shape valve plate, the high quality…
The H1C series pumps are bent axis, axial piston hydraulic units with fixed displacement for operation in open circuit. H1C series pumps are available in metric and SAE mounting configuration.
Automatic reciprocating valves CETOP 5/NG10
The most important characteristic of these power units is the motor-pump set completely bathed in the oil inside the tank. This version is offering the following advantages compared with the external motor…
Automatic reciprocating valves hydraulic operation CETOP 3/NG06
The control can be used as an emergency device in the event of power cuts.
Intermediate element with flow regulator on A and B lines
Automatic reciprocating valves hydraulic operation CETOP 5/NG10
Stackable circuit selector valves. Allows one single drive of 5 users with 4 elements connected in series. As they are moved from high performances solenoids they don’t need the external drainage.
H1V series are a family of variable displacement axial piston pumps, bent axis design, for operation in open circuit. The high quality components and manufacturing techniques make possible for these pumps…
Stackable circuit selector valves. Allows one single drive of 6 users with 5 elements connected in series. As they are moved from high performances solenoids they don’t need the external drainage.
Brevini Fluid Power catalogue Cartridge Valves / In-Line Valves
Elementi modulari con attacchi su A-B
The control can be used as an emergency device in the event of power cuts.
AM5H 2 and 3 way hydrostats. The 2 or 3 way pressure regulator type AM.5.H ensures a constant set flow rate in the presence of varying system load (pressure) by keeping constant the pressure drop (p =8…
AM3H 2 and 3 way hydrostats. The 2 or 3 way pressure regulator type AM.3.H ensure the constant set flow rate in the presence of varying system load (pressure) by keeping constant the pressure drop (p =…
SURFACE TREATMENT WITH HIGH CORROSION RESISTANCE Valve with a Zinc-Nickel surface treatment on metallic parts for a higher corrosion resistance
BS2 Single station subplates BC2 Modular components BM2 Multi station subplates
BS3 Single station subplates BC3 BC06 Modular components for XQ3 and XQP3 BM3 Multi station subplates
Six way flow diversion valves. Special solenoid valves which allow the simultaneous connection of two systems.
6 way flow diversion valves. Special solenoid valves which allow the simultaneous connection of two systems.
Inlet module units with LS line no pressure relief valve
MD10V series is a family of variable displacement axial piston pumps for use in closed circuits. The displacement is variable by means of a tilting swash plate: the oil flow can therefore be reversed over…
Emergency control lever for directional control valves ADC and AD3E
Modular check valves allow one way free flow, while preventing any flow in the opposite direction by means of a conical seated poppet. They are available on single P and T lines (see hydraulic symbols).…
Le pompe H1V PV sono state appositamente studiate per il pompaggio e il dosaggio dei componenti poliuretanici con campo di viscosita 1-2000 cSt (polioli e isocianati). Lelevata riproducibilita della portata…
Cartridge valves are basically composed of a cover and an operating unit insert in the ISO 7368 (DIN 24342) mounting frame. Each cartridge valve is characterized by 2 main way for the nominal flow (up…
BS5 Single station subplates. BC5 Modular components BM5 Multi station subplates.
Inlet module unitswith pressure relief valve (up to 20 l/min)
S5AV series are a family of variable displacement axial piston pumps designed for operation in open circuit. These axial piston swash plate design units can be used both for mobile and industrial applications.…
Modular check valves allow one way free flow by raising a conical shutter, while in the opposite direction the fluid can return by means of a small piston piloted by the pressure in the other line. They…
Inlet module units with pressure relief valve (up to 40 l/min)
Electronic amplifier plug-in version for single solenoid proportional control valves. The electronic amplifier Plug version was designed in compliance with EN 175301-803 (ex DIN43650), for direct mounting…
Inlet module units with LS line with pressure relief valve (up to 40 l/min)
Maximum pressure cartridge valves allow control of hydraulic circuit pressures up 400 bar and 350 l/min maximum flow rate (NG25). Besides the normal manual pressure regulation mode, function like electrical…
S6CV series are variable displacement, axial piston pumps, with swash plate design, for closed circuit hydrostatic transmissions and high pressure applications. The pump can be supplied as single or tandem…
Inlet module units with pressure relief valve and electrical venting valve pressione e elettrovalvola di messa a scarico
Pressure relief valves available with an operating pressure range of 4 to 250 bar. Adjustment is via a grub screw. Two base versions are available: AM2VM single on A or B, and double on A and B lines,…
Electronic regulators for single solenoid proportional control valves. The electronic control card type REM.S.RA has been designed to drive the “XD.*.A, XDP.3.A, XP.3, XQ.3, XQP.*. and CXQ.3” series single…
Electronic format eurocards for XDC3 SERIE 2 positional transducer valves control. The electronic cards type SE.3.AN.21.RSserie 3 have been planned for controlling single and double solenoid proportional…
One way non-compensated throttle valves are adjustable by means of a grub screw. Three types of regulations are available on A / B / AB lines, as shown in the hydraulic symbols.
Modular check valves allow one way free flow, while flow in the opposite direction is prevented by means of a conical seated poppet. They are available on single A, B, P and T lines, and on double A and…
Open loop proportional pressure compensated bankable flow regulators
The MAV1152 controller unit is used for the control of one proportional solenoids and additional switching valves. The proportional solenoid output is pulse-width-modulated (PWM) and optimally adapted…
Piloted valves CETOP 5/NG10 with CETOP 2/NG04 pilot valve
Directional control bankable valve with A09 coils
The SH11C series pumps are bent axis, axial piston hydraulic units with fixed displacement for operation in open circuit. SH11C series pumps are available in metric and SAE mounting configuration.
Heavy duty single Joystick base (3 swtiches) This is a rugged joystick with single axis Y potentiometer and ergonomic handle. The joystick has a spring return lever for center position. The panel material…
Piloted valves CETOP 7/NG16 4/3 and 4/2 with pilot valve CETOP 3/NG06
Directional control bankable valve with pressure relief valve and A09 coils
Modular check valves allow free flow in one direction by raising a conical seated poppet valve, while in the opposite direction the fluid can return by means of a small piston piloted by the other line…
Heavy duty single Joystick base (5 swtiches) This is a rugged joystick with potentiometer and ergonomic handle. The joystick has a spring return lever for center position. Single axis Y or dual axes XY…
AD2E Electrical control
Fingertip Single axis JCFD Developed for applications where ergonomics and system integrity are paramount, the JCFD is a compact, low profile joystick that provides precise fingertip control. Designed…
AM3VM type pressure relief valves are available with a pressure range of 2 320 bar. Adjustment is by means of a grub screw or a plastic knob. Three basic versions are available: AM3VM on single A or B…
Directional contacts for electrical monitoring of spool valve movement. Electronic built-in flow adjustment. Programming of operating curves for each power output. Possible matching to solenoid data. Electronic…
Directional control bankable valve with D15 coils
Piloted valves CETOP 5/NG10 4/3 and 4/2 with pilot valve CETOP 3/NG06
Piloted valves CETOP 8/NG25 4/3 and 4/2 with pilot valve CETOP 3/NG06
Joystick for proportional valves
Solenoid valves for use in workplaces where explosive atmospheres may occur due to the presence of gas, vapour or mist and dust.
Back pressure valves are damped in-line direct acting pressure relief valves fitted with bypass nonreturn valves. Adjustment within the range 2 320 bar is by means of a grub screw or a plastic knob, on…
Solenoid operating proportional control bankable valves
AM3RD and AM3SD valves are direct acting spool type pressure reducing and sequencing units, respectively, with one end pre-loaded by means of a spring an the other end exposed to the hydraulic pressure.…
The H1C series motors are bent axis, axial piston hydraulic units with fixed displacement for open and closed circuit. A range of flangeable valves is also available. H1C series motors are available in…
Solenoid operated valves with reduced overall sizeLE VARIANT Emergency control lever
AD5E Electrical AD5O Oleopneumatic AD5D Direct Mech. AD5L Level
H1CR series are a family of fixed displacement motors, bent axis piston designed for operation in open and closed circuit. H1CR series motors have a plug-in flange to be mounted on gear boxes, to fit on…
These pressure reducing valves ensure a minimum pressure variation on the P or A port with changing flow rate up to 90 l/min. Three spring types allow adjustment within the range 7 250 bar. Manual adjustment…
Open center inlet module for fixed displacement pumps
Solenoid operated valvesLE VARIANTE Emergency control lever
Solenoid valves for use in workplaces where explosive atmospheres may occur due to the presence of gas, vapour or mist and dust. T6 variant for mine.
© 2020 "Алтел"
Разработка Джайб
